HOMESEER MANUAL PDF

HomeSeer | 10 Commerce Park North, Unit 10 | Bedford, NH | HomeSeer. com | Doc: Consult your controller manual if you’re unsure how to do this. This user’s guide is for use with Version or later of the HomeSeer software . This guide was last updated November 10, If you are an experienced. This getting started guide is for use with the HSPRO version of the HomeSeer HomeSeer is an advanced home automation package designed to take full.

Author: Ferr Gukasa
Country: Mozambique
Language: English (Spanish)
Genre: Literature
Published (Last): 3 November 2006
Pages: 221
PDF File Size: 17.5 Mb
ePub File Size: 1.55 Mb
ISBN: 530-3-70591-531-1
Downloads: 27960
Price: Free* [*Free Regsitration Required]
Uploader: Shakakus

Category Archives: HomeSeer

Officially all parameters are supposed to be twos-complement but you can enter values greater than by using the twos-complement equivalent. Apparently a power outage had in effect rebooted the HomeSeer system. However the Zee S2 unit was installed at the far manuao of the house near the cable box.

The solution was to mankal a few lamp modules and another multi-sensor so now I had 7 nodes with several routes to all nodes. When you walk within range of the motion sensor, HomeSeer is sent a Motion event immediately. You can also put it in unused outlets under a table or chair. But maybe things are not working quite as well as you expect. Follow the instructions below to set up the HSTouch Client. After several calls with no answer and checking the HomeSeer system to see that there has been no changes since 2: Vera Vera has several versions of their UI but each of them has a similar menu structure so these instructions should work on any version.

Page 6 Homesere put, an automation event consists of an action or actions that are set into motion by one or more triggers.

When I first put the system together, it seemed to work reliably. As ofthe Z-Wave Alliance reported there were more than 1, Z-Wave certified products [3] including light switches, thermostats, door locks, water valves, garage door controllers, sensors and other homeeer. Page 8 — System Restore Doing a system restore will reset your HomeTroller S6 back to factory default and wipe nanual user data.

  COMO APRENDER A HABLAR EN PUBLICO EZEQUIEL ANDER EGG PDF

Ah… that is a problem and not every device can solve every problem.

HomeSeer Type of site. Only the Always-On nodes can. HomeSeer’s HomeTroller was also released in [6] to provide functionality similar to the PRO but at a lower price point.

HomeSeer User’s Guide

When the sensor has not detected motion for several minutes it will change state to No Motion and the light will be turned off. In December, the company’s first hardware controller PRO was released. August marked the release of HS2 software.

Page 4 Z-Wave controller if you have multiple. SmartStart uses the latest Security S2 encryption technology for all radio communication ensuring your system is secure. He Takes a Fall At 2: I had the Sheriff stop by and check on him and it turns out he was on the floor, awake but unable to move. Don’t show me this message again.

The tab on the enclosure enables secure mounting in either a standard outlet or a decorator outlet common with GFCI circuits used in kitchens and baths. All of these protocols require a plug-in to be installed. This allowed the cameras to be viewed with the HSTouch mobile app.

At first, the software was compatible with X10 light switches, plug-in modules and controllers. Express Controls Express Controls provides expert consulting services for the design and manufacture of wireless Internet of Things IoT products for Z-Wave product development teams.

If homdseer devices are not reliable, add more Always-On devices. A complete listing of compatible technologies may be found on HomeSeer’s website. Having to wave your arms in the air in the middle of dinner to turn the lights back on will lower your Wife-Acceptance-Factor WAF.

Only ON commands are sent. Since he typically would get up several times each night, my 5 hour time limit rarely false-triggered. If successful, the LED light will glow solidly for about 2 seconds and then will begin blinking slowly again. EZMultipli was specifically designed with a wide-angle lens to capture motion in any direction out to about 12 feet.

With only 3 nodes in the Z-Wave network I violated one of the key rules of a mesh network — always have more than two routes to every device.

  1992 BUICK LESABRE OWNERS MANUAL PDF

The interface type corresponds to the type of Z-Wave controller you are using. Newer Z-Wave Plus devices which have this logo on them are required to have a way to reset them to factory defaults using just the device itself. I have a few lamp switches I use for my Christmas lights which I leave plugged in year round because they help the Z-Wave network since these nodes are at the periphery of my home.

This page was last edited on 19 Septemberat And they wondered why the connection to the lock was unreliable when the hub was at the far end of the building! Excluding the node should reset it to the factory fresh state. The sensors are just a bonus in that case! Depending on the size of the Z-Wave network this process will take several minutes to over an hour.

Support & Service Options

Naturally having the hub physically close to the device being paired will also help though most devices can be paired from a distance. So the people have to be moving within range of the sensor otherwise the lights will turn off while they are still in the room! The EMTs were called and he was taken to the hospital. The Z-Wave system saved my fathers life. If desired, the HSTouch mobile app may be used to monitor and manually control the products in the home.

What sets the EZMultipli apart from the typical battery-powered motion sensors is that it is wall powered so you never need to change the batteries! Please take a few minutes to read through this guide to familiarize yourself with the steps required to set up your Z-Wave network and your HomeTroller. HomeSeer’s MyHS web service is designed to provide remote internet access only and is not required for processing of automation events in the home.

It is also a good idea to click on Full Optimize which will improve the Z-Wave routing thru the mesh network.